Welcome, Guest. Please login or register.
October 20, 2018, 10:47:04 pm

Login with username, password and session length
TRADER Feedback System
IS NOW AVAILABLE
* SBFTECH Membership Required *
435267 Posts in 37272 Topics by 9537 Members
Latest Member: Mgabski
Search: Advanced search
Advertiser Inquiries
+ My Community
|-+ Library Tech Library Tech
| |-+ Tech Articles/Sticky's Section
| | |-+ Tech Articles - Electronics/EFI
| | | |-+ How to Test the TFI Module and Hall Effect/PIP Sensor
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: How to Test the TFI Module and Hall Effect/PIP Sensor  (Read 27429 times)
Joel5.0
El Hombre
Administrator
Big Block
*****
Offline Offline

Posts: 22510


Location: Puerto Rico
Miracles?.... by appointment only!


« on: April 19, 2007, 08:54:53 am »


Click Please
Logged

ACRONYMS:
LUK  LMK  JIC  BTSTDTRT  YCYDYP  NFI-YTM  SPOBI, and the classic... DILLIGAS

'86 Mustang GT, X-303 cam, Holley DP 700, RG Tran., 289 Heads   Ford Smilie 2


Quote from: Joel5.0
The right to be stupid is inalienable for sure however, there is no such thing as a right to impose stupidity onto others
Great Thoughts will Overwhelm a Feeble Mind
There is never money to do it right, but there's always money to do it over.
Knowledge based on external evidence is unreliable.
He, who doesn't ask, does not deserve an answer.
A mind is like a parachute it only works when it is open.  (oldmanjoe)
If you can't explain it simply, you don't understand it well enough. (Albert Einstein)
Tuning on a Dyno for the track, is like swim practice in a bathtub.
I can explain it for you, but I can't understand it for you. (90lxcoupe)
The proof of understanding is the ability to explain it. (H. Torruella)
Ignorance is bliss, but stupidity is orgasmic.
Fraud and falsehood only dread examination. Truth invites it. (Samuel Johnson)
The chaotic resistance of the opponents leads to the conclusion that they are not prepared to meet the challenge. The problem is already much more psychological then technological. [Bojidar Djordjev]
Individuals are rational and humane... Crowds are reactionary and barbaric. (Jason)
The person who says it cannot be done should not interrupt the person doing it. –Chinese Proverb
Nothing sways the stupid more than arguments they can't understand - Cardinal de Retz
jpw
4 Banger
*
Offline Offline

Posts: 12

Location: hawaii

« Reply #1 on: March 17, 2010, 12:12:32 pm »

Sometimes checking voltages at module connector while it is in its no start state helps narrow the cause down. I use the following steps, all checks are with a straight pin pushed into harness side of TFI connector along side the wire to make contact with the terminals while  still connected and neg lead of meter on neg batt post KOEO.

1 Check for spark. No spark go to 2, got spark Check fuel pressure.

2 With Digital voltmeter check ICM PWR for batt volts. See diagram at http://sbftech.com/index.php/topic,593.0.html 

3 Check Coil - for battery volts, No voltage at coil- with voltage OK at ICM PWR means open coil or wiring between coil and TFI. If volts are OK crank engine and volts should fluctuate as module grounds and ungrounds coil, this is the one this that a incandescent test lamp is safe to be used on and is easier to see coil being fired ( lamp flashes w/ good sig from TFI)

4 check IGN GND for .5 volts or lower with engine cranking, lower is better higher = bad ground.

5 Check PIP while bumping engine in small increments or turning by hand, voltage should go from close to 0v to close to battery as shutter wheel in distributor passes through PIP /Hall sensor . If no good unplug SPOUT and try again. If voltage changes properly PIP sensor is usually OK.

6 By far the most common problem is no sig to fire coil at COIL- , cause is bad TFI if all other tests are have good results.

HTH j
Logged
jpw
4 Banger
*
Offline Offline

Posts: 12

Location: hawaii

« Reply #2 on: March 17, 2010, 12:14:59 pm »

Oops, I was actually trying to reply to

  http://sbftech.com/index.php/topic,24712.msg247396.html#msg247396  .

My apologies J
Logged
jpw
4 Banger
*
Offline Offline

Posts: 12

Location: hawaii

« Reply #3 on: March 17, 2010, 12:17:00 pm »

Joel,
 please move if possible.
Thank you
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  



Powered by MySQL Powered by PHP Valid XHTML 1.0! Valid CSS!
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines



408 Stroker