Welcome, Guest. Please login or register.
October 16, 2018, 07:12:32 am

Login with username, password and session length
Team Z Motorsports
Tech Section
* SBFTECH Membership Required *
435266 Posts in 37271 Topics by 9537 Members
Latest Member: Mgabski
Search: Advanced search
Advertiser Inquiries
+ My Community
|-+ Grass Roots Tech
| |-+ Grass Roots General Tech
| | |-+ 157 tooth manual flywheel for a late 80s 302
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: 157 tooth manual flywheel for a late 80s 302  (Read 1604 times)
junkyardjeff
Small Block
***
Offline Offline

Posts: 176

Location: Dayton Ohio

« on: February 03, 2018, 11:46:05 pm »

I am going to be getting a late 80s 302 that has been warmed up some that I would like to put in my 65 galaxie that has a manual trans,it has a 10 or 10 1/2 inch clutch and presume it has the smaller flywheel. The problem is I have to use this bellhousing since the Z bar ball screws in it  and the hole in the block is too far forward to use so does anyone know if a new 157 tooth flywheel is available for the newer 302s.
Logged
juiced coupe
Six figures worth of don't give a f*ck
Global Moderator
Big Block
*****
Offline Offline

Posts: 8394


Location: Pascagoula, MS
The land mass between New Orleans and Mobile


« Reply #1 on: February 04, 2018, 12:12:01 am »

5.0 Mustangs used the 157 tooth flywheel. Early to mid 80s cars used a 10" clutch, while later cars used a 10.5". Some aftermarket flywheels have both patterns.

Many 80/90s trucks came with 164 tooth flywheels that use an 11" clutch.

This may also give you some options:


https://www.dallasmustang.com/equalizer-bar-engine-mount-adapter-1965-1968-5-0-block-in-early-model.html
Logged

Doing more with less, or something like that.
http://sbftech.com/index.php/topic,20009.0.html

Quote from: Monte Smith
Bottom line, if it was the hot ticket, the fast guys would do it.............they don't

You might need some Titanium rods and a flow bench!  LMAO on floor

I honestly don't get it.

I'm sweating, my heart is racing, my clutch foot is twichin', and my right arm punched the computer screen doing an involentary 2-3 shift while reading all that. 
junkyardjeff
Small Block
***
Offline Offline

Posts: 176

Location: Dayton Ohio

« Reply #2 on: February 04, 2018, 10:28:03 am »

I did not know that part was made and will have to remember it.
Logged
scienceguy
Big Block
*****
Offline Offline

Posts: 2453


Location: West Virginia

« Reply #3 on: February 07, 2018, 08:59:37 am »

I believe you can get an OLD style 157 tooth flywheel designed for the older 'Long' style, 3 fingered pressure plate.  It has to be a fairly common swap item, as I'm sure there are lots of newer engines being swapped into older cars, and that piece would make it an easy switch.

Just look for that type flywheel with the newer 50 oz-in balance, instead of the older 28 oz-in.

Good Luck!
Logged

1966 Mustang, Toploader 4-speed
Pump Gas, Flat Tappet 306
9.88 @ 135.67
Pages: [1] Go Up Print 
« previous next »
Jump to:  



Powered by MySQL Powered by PHP Valid XHTML 1.0! Valid CSS!
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines



408 Stroker