Welcome, Guest. Please login or register.
June 23, 2017, 09:48:17 am

Login with username, password and session length
Director PLEASE!!!!
Add your location information to your personal profile. Thanx!
433650 Posts in 37095 Topics by 9458 Members
Latest Member: Rich351
Search: Advanced search
Advertiser Inquiries
+ SBFTECH.com Experienced Small Block Ford Tech
|-+ Grass Roots Tech
| |-+ Grass Roots Cylinder Heads
| | |-+ comp 1305-16 on an afr head
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: comp 1305-16 on an afr head  (Read 1971 times)
dads67coupe
Small Block
***
Offline Offline

Posts: 168

Location: Littleton NH

« on: March 05, 2017, 02:47:49 pm »

I just bought a set of comp 1305-16 magnum roller rockers, new in box. the guy had them on craigslist advertised as fitting SBF with a 7/16 studs.

He shipped them pout today and got back to me with a part number. Looks like they are 1.6 ratio for SBC instead of SBF.

Will they work on my AFR 205's? and if it makes a difference I have not bought pushrods yet

Or am I screwed again with my "good deal"
Logged
juiced coupe
Six figures worth of don't give a f*ck
Global Moderator
Big Block
*****
Offline Offline

Posts: 8118


Location: Pascagoula, MS
The land mass between New Orleans and Mobile


« Reply #1 on: March 05, 2017, 03:50:47 pm »

The geometry is only slightly different. With the long valves on those heads, I suspect that they will be just fine.

Just be sure to pay attention to the inside clearance at the guide plate.
Logged

Doing more with less, or something like that.
http://sbftech.com/index.php/topic,20009.0.html

Quote from: Monte Smith
Bottom line, if it was the hot ticket, the fast guys would do it.............they don't

You might need some Titanium rods and a flow bench!  LMAO on floor

I honestly don't get it.

I'm sweating, my heart is racing, my clutch foot is twichin', and my right arm punched the computer screen doing an involentary 2-3 shift while reading all that. 
dads67coupe
Small Block
***
Offline Offline

Posts: 168

Location: Littleton NH

« Reply #2 on: March 05, 2017, 03:56:53 pm »

ok, will do

thanks again juiced
Logged
dads67coupe
Small Block
***
Offline Offline

Posts: 168

Location: Littleton NH

« Reply #3 on: March 06, 2017, 06:45:05 am »

I have been reading and I should be able to adjust pushrod length to get a good contact pattern on the valve.

I am thinking its gonna end up slightly longer than it would for a ford rocker, but thats just sort of guessing.

any input?

Looks like most chevy rockers are .060 shorter from trunion to tip, but I have read longer as well........ wonder which it actually is
Logged
juiced coupe
Six figures worth of don't give a f*ck
Global Moderator
Big Block
*****
Offline Offline

Posts: 8118


Location: Pascagoula, MS
The land mass between New Orleans and Mobile


« Reply #4 on: March 06, 2017, 09:08:40 am »

Shorter.

But when longer valves are used on SBF heads, it's common for a SBC rocker to actually have better fitment.

Pushrod length? Measure, it is what it is.

You can have different Ford rockers, and all of them measure out a little different.
Logged

Doing more with less, or something like that.
http://sbftech.com/index.php/topic,20009.0.html

Quote from: Monte Smith
Bottom line, if it was the hot ticket, the fast guys would do it.............they don't

You might need some Titanium rods and a flow bench!  LMAO on floor

I honestly don't get it.

I'm sweating, my heart is racing, my clutch foot is twichin', and my right arm punched the computer screen doing an involentary 2-3 shift while reading all that. 
dads67coupe
Small Block
***
Offline Offline

Posts: 168

Location: Littleton NH

« Reply #5 on: March 06, 2017, 11:36:14 am »

THANKS MAN, truly grateful for all your help!
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  



Powered by MySQL Powered by PHP Valid XHTML 1.0! Valid CSS!
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines



408 Stroker