Welcome, Guest. Please login or register.
February 23, 2018, 01:35:04 pm

Login with username, password and session length
TRADER Feedback System
IS NOW AVAILABLE
* SBFTECH Membership Required *
434859 Posts in 37223 Topics by 9534 Members
Latest Member: 88_GT
Search: Advanced search
Advertiser Inquiries
+ SBFTECH.com Experienced Small Block Ford Tech
|-+ Library Tech Library Tech
| |-+ Power and Drivetrain Combos
| | |-+ 289/302 - non-stroker combos
| | | |-+ Juiced Coupes 306
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: 1 ... 18 19 [20] Go Down Print
Author Topic: Juiced Coupes 306  (Read 152865 times)
RunninHorse
Big Block
*****
Offline Offline

Posts: 3348


Location: Floresville, Texas
Órale!


« Reply #285 on: April 29, 2017, 05:30:24 pm »

Nice!  Glad you got it back to the track! 
Logged

I'm Rob.  Working on my '93 Reef Blue coupe.  Stock internal 302, 80 MAF, 75 TB, Victor 5.0, High Ports, 30# inj., B303, 1.6s, Tremec TKO 3550, Quicktime bell, Fidanza Al flywheel, stage 3 ceramic clutch, & 4.10s.  12.68 @ 111.69
'66 F100 shortbed, 352ci, 3 on the tree - on hold
'65 Coupe rolling chassis - on hold
Parts I'm selling: 
Hardened Push Rods - Trick Flow 6.2" .080 - $60
Misc. Fox Body Interior Pieces
juiced coupe
Six figures worth of don't give a f*ck
Global Moderator
Big Block
*****
Offline Offline

Posts: 8320


Location: Pascagoula, MS
The land mass between New Orleans and Mobile


« Reply #286 on: May 05, 2017, 06:34:56 pm »

Got the new fuel pump installed today, along with a wiring update.

I got a deal on a nearly new Holley Black pump, which should be more or less equivalent to the Aeromotive pump that was on it before. While the Aeromotive pump served me well, I just can't see spending $200+ on a non-serviceable pump, whereas Holley will sell you damn near anything you want.

I had also been using a generic relay from the parts store, so I took this opportunity to replace it with a waterproof Bosch piece. After taking everything apart, I could see some pitting on the terminals of the old relay.



Since I already smelled like gas, I decided to go ahead and remove and inspect all the braided lines on the car. I have been thinking about replacing all of the hose on the car, so my intent was more to make sure that none of the hose ends were galled or otherwise needed replacement.

It turned out that the lines and ends were all in good shape. The inner liners are still pliable and I didn't see any signs of degradation. So I cleaned everything up and put them back together with Corrosion Block spray.

There was one thing that I noticed. My car has a few different brands of hose ends on it, depending on what was available at the time. The newer ones are Redhorse brand. IMHO, they are much better than other brands that I've used.


* 20170505_165512.jpg (3406.14 KB, 4128x2322 - viewed 283 times.)
« Last Edit: May 05, 2017, 09:49:28 pm by juiced coupe » Logged

Doing more with less, or something like that.
http://sbftech.com/index.php/topic,20009.0.html

Quote from: Monte Smith
Bottom line, if it was the hot ticket, the fast guys would do it.............they don't

You might need some Titanium rods and a flow bench!  LMAO on floor

I honestly don't get it.

I'm sweating, my heart is racing, my clutch foot is twichin', and my right arm punched the computer screen doing an involentary 2-3 shift while reading all that. 
juiced coupe
Six figures worth of don't give a f*ck
Global Moderator
Big Block
*****
Offline Offline

Posts: 8320


Location: Pascagoula, MS
The land mass between New Orleans and Mobile


« Reply #287 on: February 15, 2018, 04:10:41 pm »

Not exactly a update on the car but this seemed like the best place to put it.

From the "Things I enjoy" thread:

Finding stuff that you misplaced or just forgot that you had.

Last year, the shaft bearing on my Aeromotive fuel pump went out and chewed up the seal with it. At one time, I knew that I had a parts pump laying around (from a friend's car that went underwater in a hurricane) but couldn't locate it. I figured that I must have thrown it out.

Anyways, I put a Holley black pump on the car and have since bought a Mallory Comp 250 for future plans. As luck would have it, I stumbled across the old parts pump while digging through some boxes. Even better, it had two regulators laying there with it.

Between the two pumps, I was able to salvage enough parts to build one good one (I think). When I get bored one day, I'll hook it up to check pressure and flow.

One of the regulators is a very old Mallory 2 port, not even the current design. Nobody at the current Mallory/MSD/Holley even knew another design existed. So, I made a thread on the YB to see if anyone knows if the new style kit will work on the old regulator.

The other regulator is a Summit brand two port, made from polymer. I remember that I cracked the housing by over tightening one of the fittings. I replaced it with a Holley 803. I thought that it might use a Holley sized diaphragm but the holes don't line up. So, if anyone has one of these and needs parts, PM me and its yours.

With a few modifications, I was able to retrofit the old Mallory regulator with the new style kit.  With the exception of not being able to adjust above 7# (the new kit has a flat diagram, compared to the original concave design), it worked quite well. While hooked to my flow gauge, it was able to adjust to below 3# and didn't have hardly any creep when the valve was closed.

I tested it with the above mentioned Aeromotive pump, which also seemed to work well. It primed fast, made no abnormal noise, and didn't leak.
Logged

Doing more with less, or something like that.
http://sbftech.com/index.php/topic,20009.0.html

Quote from: Monte Smith
Bottom line, if it was the hot ticket, the fast guys would do it.............they don't

You might need some Titanium rods and a flow bench!  LMAO on floor

I honestly don't get it.

I'm sweating, my heart is racing, my clutch foot is twichin', and my right arm punched the computer screen doing an involentary 2-3 shift while reading all that. 
al2
Big Block
*****
Offline Offline

Posts: 1702


Location: fort worth,tx.

« Reply #288 on: February 15, 2018, 07:28:11 pm »

So when is it test time ?
Logged
juiced coupe
Six figures worth of don't give a f*ck
Global Moderator
Big Block
*****
Offline Offline

Posts: 8320


Location: Pascagoula, MS
The land mass between New Orleans and Mobile


« Reply #289 on: February 15, 2018, 07:53:10 pm »

So when is it test time ?

If it happens this year, likely late November.

I start 7-12s in a few weeks, until June. Then the same thing in the fall. So, I'll be working during the good weather.

I need new tires right now. I couldn't bring myself to putting a few passes on a new set and then have them setup in hopes of getting in a few November passes.

I started to go anyways the other day on my worn tires. Then I found out that they are doing track renovations. My other local track has been running a bunch of no prep stuff.

I don't know. I don't typically like summer racing, but I may do it anyway.
Logged

Doing more with less, or something like that.
http://sbftech.com/index.php/topic,20009.0.html

Quote from: Monte Smith
Bottom line, if it was the hot ticket, the fast guys would do it.............they don't

You might need some Titanium rods and a flow bench!  LMAO on floor

I honestly don't get it.

I'm sweating, my heart is racing, my clutch foot is twichin', and my right arm punched the computer screen doing an involentary 2-3 shift while reading all that. 
David Claflin
Adv_SBFTechie
Big Block
****
Offline Offline

Posts: 7885


Location: Redneck Riviera (Ft Walton Beach Florida)

« Reply #290 on: February 16, 2018, 09:22:50 am »

Holt is only an hour or so away.......
http://raceecd.com/
Logged

1990 Red LX, 306, 75MM, ported gt40's, Holley SMII, accufab longtubes, 3" exhaust, 4.10's, 318RWHP/316RWTQ
1985 LTD LX 302, ported TW's, XE-264 cam, ported Holley SMII, 75MM-R TB, MAC 1 3/4" longtubes, 4R70W, mach 1 brakes
1988 GT long term project
juiced coupe
Six figures worth of don't give a f*ck
Global Moderator
Big Block
*****
Offline Offline

Posts: 8320


Location: Pascagoula, MS
The land mass between New Orleans and Mobile


« Reply #291 on: February 16, 2018, 01:34:42 pm »

Holt is only an hour or so away.......
http://raceecd.com/

I've definitely thought about it. Its probably closer 1.5+ for me, assuming that the parkway isn't backed up.

I'm also not crazy about towing through the tunnel and across the parkway. Its like people forget how to drive when they get there.

After watching all Rodney's videos, I'm definitely going to make it over there one day.
Logged

Doing more with less, or something like that.
http://sbftech.com/index.php/topic,20009.0.html

Quote from: Monte Smith
Bottom line, if it was the hot ticket, the fast guys would do it.............they don't

You might need some Titanium rods and a flow bench!  LMAO on floor

I honestly don't get it.

I'm sweating, my heart is racing, my clutch foot is twichin', and my right arm punched the computer screen doing an involentary 2-3 shift while reading all that. 
Pages: 1 ... 18 19 [20] Go Up Print 
« previous next »
Jump to:  



Powered by MySQL Powered by PHP Valid XHTML 1.0! Valid CSS!
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines



408 Stroker